crystal clear sound :-))
Digital Audio Out @ 2 Chip SNES with S-DSP
August 29th, 2016Recap SNES 1 Chip
August 29th, 2016UWRC Capcom Power Stick Fighter MD
August 3rd, 2016out of the 90th this Capcom Fighter Stick was a great peace of its time. I used the rarely MD Version, because I love white more as black.
Branded to capcom, nice, never seen something like this before
But its time to desolder the original Capcom heart. So we didn’t get any interfear
position of uwrc tx board
wiring
changing of charging resistor to 5,11k -> around 200mA current for the big one 3000mAH Lipo, hope not to recharge it in a lifetime
preparing of usb port/led
some pictures
capcom rules
UWRC meets NEOGEO PAD2
August 1st, 2016thanks to micro I got a TX for a great controller the neogeo CD Controller in the PS2 Version called NEOGEO PAD 2 Controller.
removing the original controller
some dremel work
wiring of uwrc
I used a 200mAh Lipo and changed the loading current to 50mA via changing loading R from 10k to 20k
loading led, usb port, lipo
done
Atari 2600 gets internal UWRC wireless Receiver
Juli 30th, 2016I used a old revision (rev1) of micros neogeo Receiver and put it inside of the A2600 6 swich.
I was modified before with A2600RGB from tim worthington and I used some more switches like select, reset from the Atari and extra button from tim worthingstons 2600RGB PCB
UWRC
Button A = normal FireButton 1 of Atari (Pin 6)
Button B = Firebutton 2 (Pin 9)
Select = Extra Button A2600RGB PCB
Start = Start of Atari 2600
Button C= Select of Atari 2600
Button D = Palette switch A2600RGB PCB
All normal Controllers will work after mod too. Like paddle, racing, joystick.
(diodes, needed to make special functions from A2600RGB working, R=10k as pullup)
RX Led to show it though the power switch hole upperside red led down side gn led
UWRC PC Engine Shuttle Controller
Juli 30th, 2016PC Engine Duo R/RX RGB Mod with bypass PCE-TV
Juli 27th, 2016Nothing really new, only to see how to add THS Amplifier working in a Duo R / RX.
I used Pin 44 of HU C6260 C-Sync for Sync. So you have to cut the Video Signal to the Din Connector (yellow wire).
Black wire is optional, for „more“ GND
For the Din Pinout I used the old French Layout born in the 90ths. With RGB added to the 3 new Pins of the Din 8.1. The rest of Pins are untouched (exeption C-Sync)
3 resistors 22 Ohm are used for make PCE-TV work to output around 0,7V. The PCB is the 1st Revision of micro. Power is taken from a Elko nearby. (orange/black=GND, orange/red=5V)
Scart Pinout
Jailbars removement
After checking the picture there are jailbars
After replacement of two capacitor the picture is great.
replace C909 and C923 with 4,7uf down under Hu C6260
You final reward will be 1000 Points
Wireless Rules
thanks micro
UWRC vs remote control yesterday
Juli 25th, 2016UWRC wire Colors
Juli 21st, 2016
9 | GND | GND | 19 | GND | GND | |||
8 | B | Button 2 | 18 | R2 | Button 10 | |||
7 | A | Button 1 | 17 | R1 | Button 9 | |||
6 | ST | Start | 16 | L2 | Button 8 | |||
5 | SL | Select | 15 | L1 | Button 7 | |||
4 | RT | Right | 14 | Z | Button 6 | |||
3 | LT | Left | 13 | Y | Button 5 | |||
2 | DN | Down | 12 | X | Button 4 | |||
1 | UP | Up | 11 | C | Button 3 | |||
0 | GND | GND | 10 | GND | GND | |||
3 | blue | GND | ||||||
2 | green | 5V | ||||||
1 | yellow | Led |
Marked R used for different current while loading LiPo
I=1000V/R
for
400mAh Lipo (Standard) ->100mA R=10k
250mAh Lipo ->050mA R=20k
3000mAh Lipo ->200mA R=5k
Voltage Regulator used: 2,3V Maximum Voltage: 5,5V